Chosen Solution Would like a diagram of how the drive belt should run. Most manufacturers have a tag on the core support by the radiator. Some put it on under side of hood. But either way, here is what I found. https://www.google.com/search?q=1992+gmc… You’ll have to look through there to find the exact one because you didn’t say if it had A/C or not. Hope this helps.
Chosen Solution Hello. My X-Box 360 S has had the E 82 error for a couple months. I have tried an AV and HDMI cable in it and the error stayed on display. The X-Box has no hard drive under the sliding plate on the side. It has a 16mb external drive plugged into the front that we have tried removing to fix the problem, but with no avail. Thanks....
Chosen Solution since update 7.50 my PlayStation Pro only shows the error SU-42118-6. would installing a new drive fix the error? or can’t I just swap the drive without the mainboard? BD-ROM Drive Error / Can Not Communicate with BD-ROM. Check BD-ROM Ribbon between motherboard and drive. If the tabs are broken, replace cable and test. Also check connectors for breaks or corrosion. If no better, check and replace drive board fuses where bad: CUH-10xx / 11xx series consoles: F501, F201, F202 and F203....
Chosen Solution Fan connector on the system board was broken. I obtained a new one, and had a local cell repair shop solder it in (since I’m not skilled with anything that small). Fan works, but runs full speed, and my fan monitoring software says 0 RPM. So I’ve got power to the fan, but obviously no tach signal coming back. Does anyone know the pinout for this? The pinout is: Pin 1: 5V DC Pin 2: Motor Control (PWM signal) Pin 3: GND Pin 4: Tach
Chosen Solution After replacing the video card in my iMac, it boots and operates perfectly except one of the fans is running way too fast. I believe it is the cpu fan. I downloaded TGP. It shows all temperatures are good. Cpu fan is running at 3600 and is red. Any idea why? Thank you, Richard Sounds like you may have pulled one of the wires out of the fan header plugged into the logic board, in this case the tach wire....
Chosen Solution Hi can someone help I don’t keep to good so I have a tall cooling fan at my bed its on 24/7 over the last month it keeps falling over and the tilt keeps dropping down it as if the fan bit is to heavy for the stand. Thank you Susan In addition to what Dave said, if the pole is wobbly on the stand, there is usually a threaded nut on the bottom of the stand where the pole goes through it....
Chosen Solution How to reset my pass code If your operating system is Windows VISTA or Win 7, press the F8 key when you see the Dell logo. It’ll take you to the advanced boot menu options, including ‘Repair your Computer’. Select that option and enter your password if needed, then you’ll see a list of options like ‘system restore’ and ‘command prompt’. The last option displays ‘Dell PC restore’, or something along those lines....
Chosen Solution This is for an 8y old 3 door Samsung (RF261BEAESP). The fridge and freezer are both not cooling. There are no error codes. The compressor is running, but no cool air. Cook tank is warm. The coolant line from the compressor to the fridge is not cool. Best guess is a coolant leak. Any thoughts? Hi @geneg , Either a coolant leak or a faulty compressor. Is the compressor hot to the touch?...
Chosen Solution Hi, I have borrowed my mates Canon EOS 7D fitted with a Canon EFS 17 - 85mm lens. I have it switched to auto focus but everyan time I try to take a shot outside the error code 01 comes up telling me there is a communication fault between the lens and camera! The weird thing is that I can take shots OK indoors but as soon as I try to take an external photo I get the error code come up!...
Chosen Solution We are unable to remove the screws to get into the battery. Do you have an address where we can send it? US Customer support info is at Phone: 1-800-226-6534 Email: cspolaroid@camarketing.com You can find other countries at http://polaroid.com/support
Chosen Solution i have an ipod nano 3rd gen 8 gb, is there a away to increase the space memory to maybe 32 or more gb? kun, only by replacing the logic board. The memory consist of IC’s that are soldered to the board and can not (normal DIY’er) easily be replaced. Take a look at step 12 of this teardown Hope this helps, good luck. no because the ipod is old and it’s not like modern technology like the iphone 13....
Chosen Solution Glass Back LG G7 ThinQ The back glass of the LG G7 Thinq is easier to replace and fix, than fixing the front glass with LCD. yes they are available with the tools on ebay and amazon.
Chosen Solution hi — does anyone know if you can replace the disk drive in this machine? and if so, how to do that? tia! @indranz yes you can. Here is what it looks like for a typical Series 5 (again, since we do not know your exact model number you will have to verify procedure)
Chosen Solution I know that it won’t work directly but I want to know if there’s any accessories that you can use to plug in og Xbox controllers into an Xbox one kylecumming1 Sorry to say but you cannot just plug it in straight to the “Xbox” one console. You will need a adapter that you plug your “Xbox” original controller into and then plug the adapter into the “Xbox” one....
Chosen Solution Hello, im trying to restore my Iphone 6 because its giving me a boot loop so i cant get in to the actual phone. I get the apple logo for like around 10 seconds and it shuts off and then turns back on. I’ve put it into recovery mode and dfu mode to try to restore it but once it reboots it shows a spinning wheel for like 1 seconds and reboots back to “ connect to itunes logo....
Chosen Solution Why want the sensor work? Usually mobile phone fingerprint solutions are individually encrypted. I cannot say Samsung phones are like this as well but it is VERY likely to be. So you cannot replace the sensor, you simply can’t. the home button you bought doesn’t have a fingerprint sensor inbuilt. that’s why it doesn’t work.
Chosen Solution Sony alpha a6000 randomly shuts down after a few minutes of being on, and when I manage to get it back on it will boot up as if it was factory reset, asking for the date and time. Francisco Lomeli , A lot of the forums suggest to make sure your software is up to date. Make sure the battery you are using is charged. The charging indicator may flash if the battery has not been charged in a while, or if it is brand new....
Chosen Solution I have a new A10 with compatible pin config. But A6 is glued to board – will glue gun damage board? Other options to remove glue? I don’t think the CPU is glued to the board. Rather, I think the CPU is Soldered to the board. If you are comfortable with soldering, you need to remove the solder from hundreds of pins and make sure the new one aligns perfectly, and that none of the pins are blocked, damaged, or blocked....
Chosen Solution Hello. A few years ago, my iPad 2 have been exposured to high pressure in my bag. And as you can guess, it’s digitizer stopped working. I’ve taken it to some phone repair services, but they couldn’t fixed it. And yesterday I wanted to give it one more shot. And bought a new digitizer. And few hours ago I have connected the digitizer to the device. But it did not work at all....
Chosen Solution Hello, is there anybody who spotted a disassembly guide for MSI GT62VR 6RE “Dominator Pro” OR maybe can create one step-by-step? I would like to change (upgrade) my RAM and 2 of 4 RAM slots are on the other side of the main board hence I need to tear down the whole laptop to get to them. Please help. @kingdomkid4 In order to remove the back, unscrew all screws marked in the screenshot than gently pull the back off....
