Chosen Solution Hello, I have a problem on my device. When I launch my Notebook, there is a clanking at the left of the pad. Thé problem is that my device can not launch windows, and stops to the BIOS. (A picture of the Bios is available below) This emplacement seems to be the hard drive emplacement. So would it be possible that the clanking is coming from it ? A video of the notebook during start up is available below....
Chosen Solution I recently bought a NES and looks pretty well from the outside, but when I opened it up to check the 72 pin connector I saw some rust on the metal pieces that I want to clean up by the best way possible. Any ideas please? Thanks! @roadrunner11 sure it can be done, but do you really want to go that route. It looks like a simple EMI shiled, so leaving it would not cause any harm....
Chosen Solution I replaced the battery in my computer. I charged it until the orange light went off. I then unplugged the power adaptor and tried to power on the computer pressing the power on key. Nothing happened. I plugged the power adaptor back in and pressed the power on key. It came on with no problem. Why does the power on key not work with a fully charged battery but work OK with the power adaptor connected?...
Chosen Solution could not restart, always showing error. want to know what to do to so that my lumia 625 can function well, it couldn’t restart or charge @mazu , John, I take it you are inquiring about the Nokia Lumia 625. It very well could be a faulty battery or connection. Below, the 1st link is a guide for changing the battery which can be used to enable the reseating of the connection first to see if that helps....
Chosen Solution I have a Nokia 1520, where can I purchase another screen from? There are 3 layers, an outer glass lens ($5) a digitizer (I bought both for $50) and an LCD. If your phone fully responds the touch it isn’t too hard to repair just the glass lens, however I wouldn’t recommend attempting to remove both the digitizer and the glass from the LCD. The glass is easily removed with a heat gun and very thin wire, however the digitizer is like egg shell, the glue holding it onto the LCD is extremely strong, the distance between the LCD and digitizer is tiny, and the polarizing film on the lcd is easily warped by heat....
Chosen Solution I changed the fuel pump, the battery & all my fuses and relays are good but it cranks and won’t start. Whenever you open a pressurized fuel system you must purge line by turning ignition key to the on position for 10 secs +/- (you should hear pump kick on and stop). Then turn key back to the off position for another 10secs and then try to start. If air is present in line the pump won’t pick up fuel....
Chosen Solution When I press the power button the indicator momentarily comes on then goes off. I performed the power and rtc reset several times with no success. My next move will be to remove the back cover and pull the integrated battery connection. If this doesn’t work what will be the next steps to isolate the problem? I am debating whether to risk purchasing a replacement motherboard or play it safe and buy a new laptop?...
Chosen Solution Hi guys! I recently bought a non-working Macbook unibody 2.0 GHZ A1278. When i opened up the back it looks like i minor liquid spill right about the magsafe board is. I am about to order a completely new logic board and DC-IN board to try and fix the problem (the macbook doesn’t boot up at all). It seems that the connector for the display data cable and the very end of that same cable has also been affected by the liquid....
Chosen Solution So, after replacing the battery in my Macbook Pro laptop, the display on the laptop looks like this: It outputs to a TV just fine. Does anyone have an idea if a connection on the inside didn’t get plugged back in all the way, or something is damaged? SMC RESET Shut down the computer.Unplug the computer’s power cord and ALL peripherals.Wait 15 seconds.Attach the computers power cable.Wait another 5 seconds and press the power button to turn on the computer....
Chosen Solution I bought a new hard drive to install Sierra but when I plug it and try to erase and format it through disk utility it gives error and fails to format to journal. however when I plug the hard drive via external via USB connection I’m able to format and complete the whole installation. Is it because it cant detect SATA drivers on the board since its new? Update (10/09/2017) The MacBook Pro “Core i5” 2....
Chosen Solution I have a furby boom crystal and it keeps shutting down. I tried to hit the restart button it starts up then it shuts down. Do I have a defective furby? If the furby does not move and just constantly shuts down, then the the small 6V brushless DC motor went wrong. I had the same issue. You can replace it with one from a PC DVD reader (this is the door opener motor)....
Chosen Solution troybilt riding mower. the gas pedal will not move. the mower will move but it is at a very slow pace. we have looked at pulleys and belts and can not visibly see anything wrong. can you help? Here’s the manual on it but I’m going to have to study it a while to able to guess what might be wrong. First bet would be the Throttle cable. Check for a blockage of the peddle, something may have lodged behind the peddle preventing it from going down....
Chosen Solution Can I replace the logic board? I have a Late 2011 15’’ Macbook Pro? My thunderbolt stoped working because a failure and the technician said that the only way it comes back is switching the logic board. But then I realised that my MacBook Pro runs Core i7 2.2 Ghz and there are 2.5Ghz mother boards avaiable to buy. My question is, switching my original motherboard to this another one can possibly bring trouble because of this difference of processor?...
Chosen Solution Symptoms: About a year ago, Sony Bravia 52" model KDL 52V5100 TV screen would occasionally be filled with vertical colored lines when turned on. Turning it off and then back on would usually make the lines go away and screen would be normal. For the past year the TV was completely normal. Recently the picture suddenly became bad but in a different way. The picture is very dark, and the left side of the screen is really blurry....
Chosen Solution I bought a one plus 10 Pro 5G and I am unable to install the automatic system update. I am alerted of new update, i am able to download it but yet it is unable to install. It throws an error and tells me to try again. I have reformatted my phone and still cant install the system update. How do I go about it?Thank you. Download the updated software build from the OnePlus official page....
Chosen Solution Here is the deal: I own an old IMAC EMC 2210, which except for some ghost stripes in the screen, works just fine for my purposes. I have inherited an IMAC EMC 2389 from a friend with the only caveat that: HE NEEDS THE HD OF THE 2389 BACK, Safe for that part, I can keep the computer. Question: (i) can I replace the HD on the 2389 for the HD of my 2210 (therefore, returning the HD to my friend and running the 2389 with the HD of my old 2210)?...
Chosen Solution I want to replace my XL Dual software completely, i am not getting any help from the market , do you have any service center or customer care center for Nokia in Karachi You can’t change on a “completely” different software. Your phone will have ONLY the Version and the O/S from the company. If you mean to update your device ROM ,that’s a completely different thing to do....
Chosen Solution Compressor only statrs in diagnostic mode. I’m thinking thermistor or control board may be the issue? However, if fridge displays correct temperatures for fridge and freezer, would that mean that thermistor works just fine? Anything else that may be broken? I replaced compressor relay just in case. It’s a kitchenaid fridge, with freezer on the bottom. Hi @pippo2001 , According to the tech sheet: The Control Board adapts the compressor run time between defrosts to achieve optimum defrost intervals by monitoring the length of time the defrost heater is on....
Chosen Solution After replacing my old power supply I put an old 250w PSU in until I get a new one. Before I put everything back I I tested to see if it would work and it did. But once I tried connecting a monitor to it I realized that there was nothing on the display. I had tried everything of my ability from onboard graphics to a different video cards, nothing was working....
Chosen Solution Hello :) Is there a tutorial about how to replace the screen on an HTC u11 life? I just cracked mine and need to replace it :( Also, I noticed I can order either the screen alone or the screen together with the frame (power and volume buttons). I’m wondering if the repair would be easier/harder if I order the screen+frame (since the price difference is only marginal). Thank you very much in advance for your help....
