Chosen Solution When i removed the usb port from the board some of the soldering pads were missing. First i tried to replace them with some pads from dead board but the board was so eaten i didn’t had any copper to solder them. So with a very thin sand paper i scratched the surface then i could see the copper. I’ve seen that people make bridges with copper wires and solder them slightly up from where usually the legs of the usb port land....
Chosen Solution My dishwasher stars to clean you can hear water spraying and sloshing around but by the end of the cycle I end up with food stuck to dishes and soap residue dried to the dishes. Sometimes it even fills with water but it never goes anywhere. I have cleaned ever part I can think of that may be plugged. I’ve tested it and sometimes it works. But recently this isn’t working....
Chosen Solution hey, my iMac (24", 3.06GHZ early 2008, NVIDIA 8800GS) has suddenly an issue with the gpu or so, while working the display went very colourful and got stuck. After hard shut off and switching it on, the display keeps stuck at the start screen (with the Apple logo). The image looks fuzzy, here is a photo of it: https://twitter.com/#!/mceuskadi/status/… Nevertheless the iMac is booting! I can hear the login sound from skype and I can ssh into my iMac using my iPhone....
Chosen Solution Dryer will not Start. Display to my dryer turns on when depressing the “Control On” button. The minutes are displayed under the “Heavy duty cycle” but when depressing the “Start” button, the dryer will not start. Also unable to choose any other drying cycle or setting when turning the knob. Just a few weeks before the the dryer not wanting to start, the drum belt was looking pretty bad so I took the dryer apart and replaced the belt myself....
Chosen Solution Alright, so the other day I dropped my iPhone 5 into the toilet, but I immediately took it out and turned it off. I then proceeded to put it into a bag of rice for the next few days. Everything works perfectly, I can use it, speakers work, everything. However, there a slight problem, the screen flickers a lot. I have it on full brightness and it constantly seems as if I’m just sliding the brightness from the lowest to the brightest....
Chosen Solution 73 F100 Electronic distributor (no points) Need correct wiring for each of these devices in my circuit: Ign switch (Blk w/grn, Yellow, Red, Pink & two Red w/grn - on one terminal ) ICM (2 + 4 w/Blue square) Starter Solenoid Ballast (ceramic 2 terminal) Coil (screw terminals) Electronic Distributor Wiring diagrams from net arent working. Henry, You might try contacting some of the companies that handle restoration parts for those trucks....
Chosen Solution Hi, I recently replacement the screen of a Black iPhone 8 plus. After the screen replacement, everything seemed to be working just fine, but egen I tried to watch a YouTube video I didn’t get sound from both speakers. I then tried to call someone, but I didn’t hear them at all. When I try to take a selfie, the front camera works just fine. Do anyone know what the issue might be, and a solution other than to buy a new flex cable for the front camera and earpiece speaker?...
Chosen Solution I have a 20" 1.8GHz iMac G5 from late 2004. It was having general instability problems so I tried putting a clean reinstall of the OS, but the process failed, three times in a row. So I ran the AHT disk which came with the machine, and it quickly failed the short test with the following error code: 2I2C/1/1:0x00000092 Sounds like it could be related to the I2C bus to me....
Chosen Solution Hello, I recently installed a Samsung 970 Evo into my Mac and restored from Time Machine. I also am using Boot Camp and the macOS partition is formatted as APFS on a GPT volume. I realized that Find My Mac could no longer be activated and my guess is that this is due to my new SSD not having a recovery partition like the original SSD. Is there a way to get this functionality back?...
Chosen Solution We have changed the batteries out but it still isn’t responding when buttons are pushed (this one has buttons in the ears, paws, feet, and on the chest). I opened it up and one of the battery coils does look rusty. Is there a safe way to clean it? Any other ideas for us? MATERIALS NEEDED: Safety items (rubber gloves, mask, eye protection)Cotton swapsWhite vinegarPencil eraser The corrosion is caused by potassium hydroxide which can leak out of the alkaline batteries....
Chosen Solution I have samsung galaxy s3. WHen i charge it gets charge easilly but when i connect to pc it doesnot recognized. I tried lot of other ways but none of methods worked for me. My friend said that software changing can fix this problem. Now i am confused that if mtp mode doesnt shows on pc but chrages then can i flash. And if not then what method i use....
Chosen Solution Why my tablet keep going back and forth to the main screen off and on If the tablet’s display is misbehaving even when no buttons are being pressed, then please try a hard boot by removing the battery and reinserting it. Also, try a factory reset of the device to replace the software with a new configuration.
Chosen Solution Hello , Im using iphone 5c and having a big problem with my screen . When im using my phone, sometimes it gets flikering all over the screen . When i sleep my phone and turn on again , it will be dispersed for a while and came back . I looking for answer a few day ago and found out you have to reattach the screen from the phone and turn it back on ....
Chosen Solution With the previous version you could change the language in the settings menu but the option doesn’t seem to be available with the DX. Can the language be changed? @bcampbel , Brian, It appears the ability to change the language setting on Vtech Kidizoom Smart Watch DX model has been removed. Find the manual below. Just a thought, I put the link to vtech support also, maybe they do have a way to change the language and accidentally omitted it, would not hurt to ask....
Chosen Solution Can you fix a funtab cracked screen? hello how are you? short answer is yes the screen can be fixed. Any device that can be built can theoretically be fixed. the longer answer is though if you can find the parts, how difficult is the repair and whether or not frankly is it worth it. If you can find a replacement screen then I/you could realistically fix it. but will the screen cost nearly as much as just getting a new one?...
Chosen Solution My printer does not print word documents. PDF documents are printed absolutely fine. how can i fix it please. Is this a windows computer? Yes? Install new correct latest printer drivers from Epson site.
Chosen Solution I have diagnosed my se v6 2003 Altima it read bad msg sensor and high voltage it throttle sensor system correlation b and e …. So I put a new msg sensor and new electronic throttle pedal in the vehical . I start the car and it runs right up the rpm scale for exactly 2 depressions of the gas pedal … up to 6…7000 be rpm but on the 3rd depression of the pedal it slips back into limp mode ....
Chosen Solution Engine will not idle runs rough backfires stops running Update (06/15/2019) Someone said it may be idle sensor ,Put new battery in starts up ok just want idle smooth On page 6-52 is the Idle control troubleshooting. https://www.hondaservicerepairmanual.com… However, this reminds me of a MAP Sensor problem. Does engine speed up and slow down between 1500RPMs and 3200RPMs when ideling, If so it’s the MAP. If not it’s vaccume leaks....
Chosen Solution I have a 1997 Ford mustang and got new battery it starts fine my battery gage dont show battery is fully charged and I got a new alternator and I checked the fuses but my battery and alternator wont keep charge is anyone having this problem Lead acid car batteries don’t like being discharged and tend to “expire” in ~5 years. Check when your battery was made and if it’s 5 years old or older, try replacing it and see if that helps first....
Chosen Solution My Nissan Maxima Isn’t Turning Over When I Try To Start It , It Gives A Crank But Isn’t Turning Over , My Fans Constantly Run And My Battery Drains Out Within Mins. Was Told It’s My ECM But I’ve Order A Programmed One And Installed It And Still Having The Same Issue. Checked All Fuses And They Were Good. Car Isn’t In A Fail Safe Mode , Security Light Flashes And Isn’t Solid....
