Chosen Solution
Canon printer pixma MG6350 doesn’t print and showing suport code 6000?
From the canon support page, that error code 6000 list a couple possibilities such as a something preventing the feed tray from opening either by blocking the printer, an unseen friction, and a possible paper jam inside the printer. http://www.canon-europe.com/Support/Cons…
I noticed that when I turned on the device, the ink cartridge holder was on far left and it wasn’t moving like it was suppose to. It was stuck. So I pushed it over a littler on left, turned on device and that seemed to work.
short version: fixed this by finding paper jammed in 2 separate places. long version: Had 6000 and then 6001 error on MG7751. Paper had been repeatedly jamming at back of paper tray. First solution was to remove paper tray and then turn over printer on its side to find jammed paper underneath at rear. But that wasn’t enough and I still had the 6000 and then 6001 error. Going deeper I found that I could remove the panel at the rear of the printer AND another curved component just behind that. This revealed another jammed sheet which was easy to remove. The two printer pieces were easy to put back in place. Then I had to restart the printer, after which it did that Canon thing of clicking a whirring for a few minutes before finally printing again.
Okay, I had the Similar Issue With My Printer Today So i did Some digging Online & After talking to Canon Support & Hours Of Time Spend Here is Something You Can Try that may solve the issue Reboot the Printer Using the Power Key. Press the Power Key & Hold it for 20-30 seconds While the Printer is Plugged to power Supply.Open the Printer Cover Clean the Dust, Small Pieces of Paper & Unseen Tiny Objects Stuck to paper feedRemove any obstacles Blocking the Printer Paper Feed & check to insure the paper feed try is Set Properly. Please let me know if this Helps you Address the Issue.
Do following: Verify that your printer tray is properly set.Remove the object they they are placed in front of printer.Clean if there is any piece of paper or something else in printer.Clean the encoder strip with soft cloth. I hope with these points your issue might be resolved if not then check Canon Pixma Mg6350 Manual to troubleshoot your printer.
Had Service Error 6000 on my MG5750. The ink cartridges would just stay on the far left of the printer. I moved them to right side of the printer and saw some paper stuck in some white cogs on the far left of the printer ( quite hard to see, I had to stand the printer up on its side). After that I restarted and no more error code, working fine now. Hope this helps!!!
In my case (model G1010), i pushed the cartridge to the right side. And on the far left side found a small piece of paper (toll ticket) stuck in the gears. I didn’t see it before because the cartridge was blocking the view. It fixed the issue for me.
Mine was a real paper jam on MG5650, so try looking for jammed paper first.
Turn on the printer while holding the stop button, don’t let go until the printer stops making noise or you get to the main screen. I don’t know if this will solve it, but this is what I did and it cleared the error message.
I have MB5070, actually when i opened the front cover and moved the ink with my hand to the right then found a lizzard stucked on the wheel kind thing, after removed the lizzard using scissor then the other half of its body got cut then disappeared , maybe felt under it, then the problem solved
i fix it by my self the problem is in the same paper holder the base so you need to push it down a bit (it pose spring) so it well be pushed after that restart it and it well work properly in sha allah my regards .
Error 6000. MG 8651. Fixed by pulling ink holder from far left back to the right. Removed paper Tangled in cogs on far left. Awkward to get at….used kebab skewers to remove. Thanks.
I got the same problem. No paper was stuck anywhere (check front and back). The ink holder was on the far left. I manually pull it back to the far right. Then I did a factory reset: find the stop button by starting the printer and stop it again. Then press the stop button two seconds, then keeping it pressed, press the power button. Release stop buttom and press it 5 times. Release power button. After doing all this, it start working again
I had to face the same problem From the canon page, that error code creates a list a couple of possibilities such as something preventing the feed tray from opening either by blocking the printer, unseen friction, and a possible paper jam inside the printer. I solve this issue through the canon pixma printer setup website: https://www-canoncomijsetup.com
Canon printer help and support (https://bit.ly/3A4YTWA) Some times, canon printer’s setup is hard to do at your own and many times you can actually experience issues with the printer. These issues can surely be resolved by canon technicians. Getting in touch can do the same and let you resolve everything. Now the ultimate part falls to the end that how you can get the canon printer help and support? All you got to do is just go to our website canon printer support and dial the toll-free support number of canon technicians and tell them about your hardware issues, low printing issues, cartridge issues and they are ready to solve them at once. VISIT OUR WEBSITE: https://bit.ly/3zZXbWf
